FreshRSS

🔒
❌ À propos de FreshRSS
Il y a de nouveaux articles disponibles, cliquez pour rafraîchir la page.
À partir d’avant-hierFlux principal

Synology Unofficial Memory on DSM 7.1 – DS920+, DS220+, DS720+, DS420+ and DS1520+ NAS

1 juin 2022 à 01:19

Using Synology NAS, DSM 7.1 and Unofficial Memory Modules for DSx20+ series

NAS systems are not cheap and nor are the accessories! However, one area that many new/existing NAS buyers take issue with more than most is the cost of official NAS memory. It’s an unfortunate fact that any computer system that has been built/tailored towards a specific purpose, is going to end up costing more. This usually comes down to much more specific design requirements and NAS drives are no different. But when it comes to Memory modules, people are slightly less forgiving. When a NAS brand sells it’s branded memory, many are quick to raise that the brand rarely makes the memory itself and instead they are putting their branded labels on memory from the likes of Kingston, Samsung, ADATA or Crucial. Now, this is only partially true, as brands tend to test a wide range of memory in the development phase of their products and then settle on the best choice based on that system architecture (no doubt factoring cost of course too) and then THAT memory is made the brand’s recommended choice, labelling it brand-approved. Where things get murky is when brands start to become rigid on their system’s use of other memory and how that impacts brand support and how the system treats ‘other’ or ‘unofficial’ memory.

Article Chapters to Skip Ahead

In the case of Synology, this can lead to DSM 7.1 displaying a warning notification in the software highlighting the use of an unsupported memory. There is also the fact that the brand might become less able to assist you in any warranty claims from reasonable system hardware failure if the issue can be stemmed in any way to memory. Now, when Synology released the latest revision of their software, DSM 7.1, there were some reports online of users stating that their system would no longer boot with 3rd party memory installed. Although I tested this on the NASCompares YouTube channel with mixed results, I have since RE-TESTED this (on the heavy request of users who did not experience any issues, who queried the results) and in that follow-up testing, ALL 3rd party memory modules worked (video embedded later in the article below). So, it looks confirmed that unofficial/3rd party memory STILL WORKS in DSM 7.1 at the time of writing, which means users still have a choice of choosing the 3rd party RAM route or sticking with the officially provided and branded memory. Nevertheless, many users who look at Synology’s pricing for their official memory modules might be thinking “HOW MUCH???”:

Important Considerations about Synology NAS and Unofficial Memory Upgrades

Now, let’s get serious real quick. A Synology NAS does not occupy the same importance in your hardware environment as a TV, sound system or even day-to-day PC. A NAS system will often be one of many backups of ALL your data! Therefore exercising caution on how your upgrade/tinker with it can have more dire consequences than simply breaking it – it can lead to the potential loss of genuinely irreplaceable photos, videos and more. Therefore if you are looking at upgrading the memory of your NAS drive and using hardware that is not on a recommended list by the manufacturer, you need to make sure you have your backups in order – have at least two backups (i.e 2 complete copies of your data OUTSIDE of the original file – one on your phone and one on a NAS only means ONE copy!). Additionally, if/when you install ANY new memory, it is highly recommended that you run a quick(ish) memory test using the desktop Synology Assistant application (for Windows/Mac) so that the NAS can check that the memory is good-to-go. Be warned, this process can take several hours (a relatively simple 2GB Transcend DDR4 2400Mhz SODIMM module in a DS920+ in my testing for a YouTube video took just over 1 HOUR and 40 MINUTES) and during that time, access to the NAS is largely impossible (plus the system will re-boot at least once). So ensure you do this during a quicker/downtime moment for your network. Below is a brief overview of where the Memory Test setting of Synology Assistant is and how to enable it:

We conducted a wide range of tests of memory from Crucial, Transcend, ADATA, Kingston, Sabrent and ADATA DDR4 SODIMM memory. These tests were conducted with a Synology DS220+ and DS920+, each running DSM 7.1. Here are the results from a video over on NASCompares:

So, let’s discuss 3rd party memory, Synology NAS and DSM 7.1 on some of the brand’s most popular systems for home/prosumer users – as it is these users who are less inclined to choose the official memory route.

Synology DS920+, DS220+, DS720+, DS420+ and DS1520+ NAS Memory Tested

Now, before getting to the confirmed working memory that works in DSM 7.1 on the popular Synology Plus Series NAS right now, it is worth remembering that official Synology memory is always going to be the ‘ideal’ choice for the NAS. Despite reservations of price and (in some places) availability, this is still the memory that is going to present you with the least hurdles in the event of ALL support claims with Synology. Additionally, official memory will ensure no ‘warning – incompatible/unsupported memory installed’ message being displayed in DSM 7.1. Most home users will be able to ignore this warning no doubt, but if you are installing a Synology NAS for a 3rd party (friends, family or professional installation), it might un-nerve the receiver. It is for reasons like these that you might still want to opt for the official Synology memory. In that case, you can find the official memory modules available from Synology here:

D4NESO-2666-4G

D4ES01-4G (ECC)

D4ES01-8G (ECC)

D4ECSO-2666-16G (ECC)

However, we have been testing ALOT of memory with the Synology Diskstation Intel J4125 and Intel J4025 series of NAS devices since DSM 7.1 was released (DS920+, DS220+, DS720+, DS420+, DS1520+) and the following 3rd party memory modules are all confirmed to work in those systems.

IMPORTANT

  1.  The Synology DSx20+ series of NAS devices all arrive with default 2GB or 4GB of memory internally that is attached to the controller board/PCB which CANNOT be removed. Therefore you will ONLY be able to install a single memory module to upgrade these systems.
  2. When installing a new memory module, the Synology NAS system may take longer than usual to boot that first time (as I found out to my somewhat embarrassing error!), so give the system upto 20mins to boot the first time you install a new memory module.
  3.  The Intel CPU inside these systems has a maximum memory support of 8GB and they recommend that all memory matches the frequency/speed (Synology provide 2666Mhz DDR4 on these systems). So, try to err towards 2666Mhz (though we have successfully tested both 2400Mhz and 3200Mhz). Additionally, having in excess of 8GB is not guaranteed to mean the CPU can actually use more than 8GB in its architecture internally.


4GB Confirmed to work on DS920+/DS220+/DS720+/DS420+/DS1520+

The following 4GB Modules of DDR4 SODIMM memory have been tested in the DS920+, DS220+, DS720+, DS420+ and DS1520+ NAS running DSM 7.1. The Links used below will take you to amazon (it SHOULD re-direct to your own country/storefront automatically) where this memory is available. HOWEVER, thanks to their site having a policy of substituting product links to something else in the event the original product is out of stock, MAKE SURE to check that the memory modules for 16GB and 32GB SODIMM modules are DUAL RANK or ‘DR‘, as Synology NAS typically have trouble with SR/SINGLE RANK modules above 8GB. When in doubt, use the model ID.

Kingston KVR26S19S6/4

2666Mhz, Single Rank

AM-D4NESO-2666-4G

2666Mhz, Single Rank

Crucial CT4G4SFS8266

2666Mhz, Single Rank

$23.25 (18/05/22)

Find on Amazon >

$34.95 (18/05/22)

Find on Amazon >

$33.77 (18/05/22)

Find on Amazon >

 

TimeTec 76TT26NUS1R8-4G

2666Mhz, Single Rank

Transcend M2666HSH-4G

2666Mhz, Single Rank

SK Hynix HMA851S6CJR6N

3200Mhz, Single Rank

$31.99 (18/05/22)

Find on Amazon >

$26.49 (18/05/22)

Find on Amazon >

$15.99 (18/05/22)

Find on Amazon >


8GB Confirmed to work on DS920+/DS220+/DS720+/DS420+/DS1520+

Now, when it comes to 8GB Memory modules on the DS920+, DS220+, DS720+, DS420+ and DS1520+ NAS running DSM 7.1, it is once again worth remembering that the CPU has that 8GB recommended maximum memory in place from both Intel and Synology. So, although all six of the tested modules below WORK, the jury is still out on whether you will be able to use them to their fullest extent. Additionally, remember that this will be paired with the 2/4GB of memory that the NAS has soldered to the controller board internally, so you will end up with either 10GB or 12GB of visible memory inside your NAS.

TimeTec 76TT26NUS1R8-8G

2666Mhz, Single Rank

SAMSUNG M471A1K43CB1

2400Mhz, Single Rank

Crucial CT8G4SFS8266

2666Mhz, Single Rank

$28.99 (18/05/22)

Find on Amazon >

$27.75 (18/05/22)

Find on Amazon >

$38.50 (18/05/22)

Find on Amazon >

 

ATech AT8G1D4S2666NA0N12V

2666Mhz, Single Rank

Sabrent Rocket SB-DDR8

3200Mhz, Single Rank

ADATA AD4S240038G17

2666Mhz, Single Rank

$31.25 (18/05/22)

Find on Amazon >

$49.99 (18/05/22)

Find on Amazon >

$55.80 (18/05/22)

Find on Amazon >


16GB Confirmed to work on DS920+/DS220+/DS720+/DS420+/DS1520+

Finally, we have the largest current memory that works in the DS920+, DS220+, DS720+, DS420+ and DS1520+ NAS running DSM 7.1 – 16GB in a single DDR4 SODIMM non-ECC module. For many users, the idea that a 16GB RAM stick for their NAS from Kingston, Crucial or Samsung will cost less than a 4GB official module is just too damned tempting! Much like the 8GB modules, it is really important to remember that these are substantially higher than the recommended maximum of the CPU by Synology and Intel, so although these have been tested and confirmed to work by both me (Robbie @ NAScompares) and many online sources, I would still ensure you have at least 2 backups in place of your data at all times regardless. 

TimeTec 76TT26NUS2R8-16G

2666Mhz, Dual Rank

SAMSUNG M471A2K43CB1

2666Mhz, Dual Rank

Crucial CT16G4SFD832A

3200Mhz (2933/2666Mhz)

$52.99 (18/05/22)

Find on Amazon >

$77.00 (18/05/22)

Find on Amazon >

$73.99 (18/05/22)

Find on Amazon >

 

Crucial CT16G4SFRA266

2666Mhz, Dual Rank

Sabrent Rocket SB-DDR16

3200Mhz, Dual Rank

ADATA AD4S3200716G22

3200Mhz, Dual Rank

$67.39.99 (18/05/22)

Find on Amazon >

$74.99 (18/05/22)

Find on Amazon >

$98.00 (18/05/22)

Find on Amazon >

Is Upgrading the Memory on a Synology NAS worth it?

Many users will avoid updating default Memory on a Synology NAS server while it is still under warranty – thinking that “if it ain’t broke, don’t fix it”. However, If you are buying a Synology NAS that supports an official or unofficial user memory upgrade, there’s almost no reason not to do the upgrade. There are practically no disadvantages (none at all, if you buy official Synology Memory) and the benefits will be immediate. You can always wait till later on an upgrade when you notice a drop in performance, however, I would keep an eye on deal websites for your compatible DDR3 or DDR4 Synology NAS supported memory and then grab some when a bargain appears. I do wish some lower capacity NAS’ drives, such as the DS120j, DS220j and DS420j (that arrive with much less memory soldered to the motherboard than their CPU can handle at maximum) were able to have their memory upgraded, as this becomes a tremendous bottleneck. There are cases where two drive bays are enough in terms of total available storage space (especially with 18TB Seagate and 20TB WD Red NAS drives in-coming), so you will be able to run a lot of applications, for multiple users, but the rather comical 256MB, 512MB and 1GB memory available in these budget models is just not enough to run DSM 7.1 to its full potential on these NAS and the result will be that most users will walk away with a very poor opinion of the Synology NAS experience.

Looking for Other Synology NAS and Compatible Unofficial Memory?

We have made several guides on finding the right unofficial memory that can be used on Synology NAS systems over the last few years. You can use the huge guide liked below to scroll the current available range of NAS from the brand and the official and unofficial RAM that works with it.

Synology Unofficial Memory Upgrades – 2022 UPDATED (Click Below)

 

📧 LET ME KNOW ABOUT NEW POSTS 🔔

Enter your email address to subscribe to this blog and receive notifications of new posts by email.

Join 1,263 other subscribers


Get an alert every time something gets added to this specific article!


Want to follow specific category?

This description contains links to Amazon. These links will take you to some of the products mentioned in today's content. As an Amazon Associate, I earn from qualifying purchases. Visit the NASCompares Deal Finder to find the best place to buy this device in your region, based on Service, Support and Reputation - Just Search for your NAS Drive in the Box Below

Need Advice on Data Storage from an Expert?

We want to keep the free advice on NASCompares FREE for as long as we can. Since this service started back in Jan '18, We have helped hundreds of users every month solve their storage woes, but we can only continue to do this with your support. So please do choose to buy at Amazon US and Amazon UK on the articles when buying to provide advert revenue support or to donate/support the site below. Finally, for free advice about your setup, just leave a message in the comments below here at NASCompares.com and we will get back to you. Need Help? Where possible (and where appropriate) please provide as much information about your requirements, as then I can arrange the best answer and solution to your needs. Do not worry about your e-mail address being required, it will NOT be used in a mailing list and will NOT be used in any way other than to respond to your enquiry. [contact-form-7] Terms and Conditions Alternatively, why not ask me on the ASK NASCompares forum, by clicking the button below. This is a community hub that serves as a place that I can answer your question, chew the fat, share new release information and even get corrections posted. I will always get around to answering ALL queries, but as a one-man operation, I cannot promise speed! So by sharing your query in the ASK NASCompares section below, you can get a better range of solutions and suggestions, alongside my own.  

 

Synology & 3rd Party Hard Drives – What You CAN and CANNOT Do

13 juin 2022 à 01:53

Synology 2022/2023 NAS and WD & Seagate Hard Drive Compatibility

If you have been considering a large scale business or enterprise NAS solution from Synology in 2022/2023, then there is a good chance you have heard about a relatively recent change in how Synology has approached hard drive compatibility in this tier of their portfolio. This change (in brief) is that this tier of systems is only designed to be used with their own branded range of hard drives and SSDs (the HAT5300, SAT5210, HAS5300, etc) and practically all hard drives from long-standing partners such as WD and Seagate are not officially supported in their business/enterprise-scale systems. Now, it is important to stress that this is NOT a complete closed-door policy here. Indeed, after the initial negative reception to this policy change demonstrated in DSM 7 featured in the DS3622xs+ and DS2422+ reveals (Danger notifications, limited drive interaction options in storage manager, etc), Synology changed a number of these areas in their DSM 7.1 system when using 3rd party drive media. However, many users are still concerned with where they stand on using popular NAS hard drives such as Seagate Ironwolf, WD Red, Ultrastar and EXOS in their brand new Synology NAS drive. So, today I want to go through pretty much everything that you CAN and CANNOT do with 3rd Party hard drives in the larger scale Synology NAS drives with DSM 7.1 right now. However, if you are in a rush or just want the TLDR:

The GOOD News

  • Practically ALL Storage Services and Features of Synology’s DSM 7.1 platform are available when using 3rd Party HDDs (Seagate Ironwolf, WD Red, Ultrastar, etc) and I only found 2 things that weren’t (and even one of those is pretty small)
  • Thanks to recently released specifications and compatibility on the DS1522+ and RS422+ NAS for 2022, we can confirm that these system do NOT have limited HDD compatibility listings and in fact list all the usual HSS and SSD models you would expect
  • Synology has changed the red ‘DANGER/CRITICAL’ warning in the DSM notification panel of DSM 7.0 to show ‘Warning’ in amber. Still not ideal, but still a step up visually
  • SMART, testing, Scrubbing, Hot Spare, Drive management and ALL RAID configurations are available to 3rd party HDDs
  • ALL File Management tool are available with Volumes that contain unverified drives
  • ALL 1st Party Applications that I tested did not complain/refuse the use of volumes that contained 3rd party media

The BAD News

  • ALL non-Synology HDD/SSD is listed in Red in the drive manager as ‘unverified’. I wish (if they have to go down this road) that they list in amber or use less loaded terms
  • Even simple hard drive utilities in the Storage Manager to build a RAID pool and volumes are met with ‘unverified/incompatible warnings 3-4 times throughout, which can be jarring
  • Warning in DSM 7.1 GUI is always present
  • Still 100% unconfirmed but in my testing, Seagate Ironwolf Health Management was not visible in the DSM 7.1 Storage Manager via the 22′ Series NAS I used
  • HDD/SSD Firmware Update checking in DSM 7.1 Storage Manager only available to Synology Drives (eg HAT5300) and not supporting 3d party drives. Not unexpected, as it would require a big chunk of database maintenance management on the Synology side to provide this feature with multiple HDD brands.

Skip Ahead:

Important – Currently only Enterprise and Large Scale Synology NAS systems released from the 2022 Series onwards have stricter HDD/SSD compatibility in DSM 7.1. Smaller-scale home user, prosumer and SMB systems under 8x Bays still have compatibility and supported HDD/SSD for WD, Seagate, Toshiba and more. This article was made and detailed using a Synology DS2422+ NAS, supplied by CCL here. So, let’s get down to business. Here is what you would find if you look up hard drive and SSD compatibility on a large business class Synology NAS drive via the official brand’s support pages (in this case, the Synology DS2422+ 12-Bay NAS system):

Now, as you can see, the available list of compatible/supported drives is almost exclusively Synology branded drives. But what happens when if we were to ignore this and install drives that were not included on this list?

Synology Notifications, Warnings & 3rd Party HDD/SSDs

There is an exception (a Western Digital Ultrastar HC310), but there have been a few exceptions in the available drives list that have tended to be the result of Synology not providing a specific drive-based encryption method/on-board feature, capacity or media interface, but as time has gone on this has diminished. In order to get a better and more complete test range, I installed four Synology HAT5300 drives and eight hard drives that covered the bulk of popular currently available HDDs for desktop and rackmount NAS server use. These included WD Red, Red Plus and Red Pro, Seagate Ironwolf and Ironwolf Pro, Western Digital Ultrastar, Seagate EXOS and Barracuda (that last one was just because I had it spare and wanted to check). As you can see in the diagram below, all eight of the non-Synology branded drives were listed as unverified and the system status in the bottom right of DSM was displayed as ‘Warning’.

A closer examination shows us that the warning is guiding us toward the storage manager area to rectify a problem. This is something that some users have already voiced their concerns over (and subsequentially Synology changed their messaging after feedback since the DSM 7.1 update was rolled out).

These notifications are also triggered in the events log at the top right of the screen and each HDD that I installed resulted in the system creating a warning alert for each. At least the nature of this alert was defined a little clearer and made reference to the drives installed not being featured on the official compatibility list for this device.

In order to see the extent of how the system interprets and interacts with 3rd party storage media in this 2022/2023 generation NAS, I wanted to go ahead and create a single drive storage pool on the WD Red Pro HDD and then create an accompanying Volume inside. So, this was Storage Pool 1 and Volume 2 (with Pool & Volume 1 is comprised of Synology HDDs). You can see that the 8x 3rd party drives (so, regardless of in/out of the pool+volume I created) as displayed in red at all times.

Looking at a single drive in the HDD/SSD tab of Storage manager shows lots of hardware information about the drive that is installed, much like any other drive. I am pleased that you are still able to see/monitor the 3rd party drives in this NAS still in DSM 7.1, even with the alert in the events log.

If you visit that alert in the events log, you can see a little more information on the nature of the alert. The event detail is a little brief, but Synology’s position on this subject is quite clear and although there is zero talk of the system not being supported by the brand down the line, they do add that they recommend using drives on the official compatibility list (ie, in this case, the bulk of which being their media) to ensure system performance and prevent data loss.

Using 3rd party drive media in the storage pool creation wizard is still possible and Synology has not attempted to block/suspend this in any way in DSM 7.1. That said, it will present you with a further warning with each screen (this one being a pinch more heavy-handed though). I know Synology want to be abundantly clear on this and want it presented that you are proceeding on a course that they do not recommend, but less experienced storage users might bulk at this warning.

When the storage pool that is made up of 3rd party storage media is created, it will be available to view alongside all other storage pools in the storage manager of DSM 7.1. The same goes for if/when you create one or more volumes inside that storage pool, but all storage associated with the 3rd party storage media will be labelled as ‘at risk’ as the pool contains “one or more drives that are unverified”. So, right now we 100% can use 3rd party drives in storage pools and volumes, but they are not without the warning in place. Let’s take a closer look at the rest of the storage manager options in DSM 7.1 and how much they can be used with 3rd party drives.

Synology Storage Manager and 3rd Party HDD/SSDs

3rd party hard drives in a large scale/enterprise 2022/2023 NAS still have the drive health information options available when selecting them in the storage manager. They are still listing with an angry red ‘unverified’ message, but health status, check history and S.M.A.R.T are still available to check the drive. In my testing, I was not able to see the Seagate Ironwolf Health Management tool (that is included on Seagate Ironwolf HDDs and visible in the NAS GUI normally), but I did not have sufficient media to identify if this was related to the new DS2422+ not supporting this feature or DSM 7.1 not allowing the featuring in the storage manager at this time.

The smart testing tab, when comparing the number of options provided in the DSM 7.1 storage manager between Synology HDDs and 3rd party HDDs, was pretty much identical! Below is how they appear via the web browser, side by side.

As mentioned, pretty much all the services and features of DSM 7.1’s Storage Manager are available to non-Synology drive media, such as the usage analyzer.

The same goes for if you choose to use 3rd party drives as hot spares (i.e accessible replacement media for if a RAID storage pool fails). You still need to ensure that the drive media in question is sufficient capacity, but it’s still good to know that hot spare use is still available.

Continuing, you also have the option of improving/changing RAID storage pools that are comprised with 3rd party drives still. This is reassuring to those that were concerned that their WD/Seagate storage pools might not be expandable/scalable in DSM 7.1 as needed on these enterprise and bigger scale solutions.

I was also surprised that the Drive Benchmark tool in DSM 7.1’s storage manager still could be used by 3rd party drives. Although this is a small tool, it can be remarkably handy for testing drives sustained activity on the fly. This tool worked with both 3rd party HDD and SSDs in testing still.

Options for scheduled or immediately actioned Data Scrubbing were also available to 3rd party drives still. Another useful and often overlooked RAID maintenance that I’m glad is still available in DSM 7.1 with non-Synology Drives.

The in-built SSD Cache advisor (the tool that recommends the level and capacity of SSD that you need to factor into your daily storage is also more than happy to interact with storage volumes that are built of 3rd party drives too. As the DS2422+ I used for these drive tests does not feature m.2 SSD slots, I was unable to confirm whether the system would accept 3rd party SSDs for caching in this enterprise DSM 7.1 NAS system. I COULD have used the E10M20-T1 or M2D20 PCIe cards to add storage, but then that would introduce an additional component into the mix and those cards also arrive with their own SSD compatibility listings already.

Overall, the big takeaway in the Synology DSM 7.1 Storage manager when it comes to using 3rd party HDD and SSDs is that you can do pretty much EVERYTHING with these drives as you can do with Synology’s own storage media. The only things that were not available were the ability to upgrade HDD/SSD firmware from within the software (something that is understandably only available to Synology media for reasons for database maintenance and accuracy I am sure) and I was unable to completely confirm whether Seagate ironwolf health management was available. EVERYTHING else in Storage Manager is available to be used. However, the lines Synology have drawn with regard to their system are pretty clear, with warnings at every screen and a persistent warning on the desktop GUI. Let’s go up a level and look at how the systems file management and more general storage tools interact with pools/volumes that are comprised of 3rd Party Media.

Synology File & Folder Management and 3rd Party HDD/SSDs

Much like when I explored many areas of the Storage Manager in DSM 7.1, I found virtually nowhere in the general system applications where using 3rd party media-built volumes presented a problem or limitation to the user. First up was File Station and (probably one of the earliest and most important things you will do) I was able to easily and quickly create a shared folder on a 3rd party drive volume as easy/seamless as normal.

The Shared Folder had ALL of the usual configuration options available (visibility, recycling, compression where appropriate, etc) and because BTRFS was still available during the volume’s creation, those benefits were also available to this shared folder too. Interestingly, there were no warnings or recommendations by the system when using this particular pool (unlike the louder stance during the storage pool/vol creation) and, spoiler alert, I never again in my testing was presented with any warnings or recommendations by the system during any further interactions with tools and services.

The file manager presented no limitations or restrictions in its services when used with 3rd party drive foundation volumes and that means that if you are considering a Synology installation for a client/associate and are concerned that their access outside of the DSM 7.1 primary browser GUI will show them warnings regarding non-Synology HDD media, this will not be the case and so far it seems that these amber indicators do not go further than the default storage setup, desktop widget (which can be disabled in 1 click) and the alerts log. Let’s test a variety of popular Synology applications to see if there is any kind of reference to drive compatibility or limitation in their presentation.

Synology Applications in DSM 7.1 & 3rd Party HDD/SSDs

There are ALOT of Synology first-party applications available in DSM 7.1 and chances are that you are going to be using at least 2-3 regularly (backups, multimedia, surveillance, collaboration tools, virtual machines, general sharing, etc), so knowing if the use of 3rd party storage media in a large scale or enterprise Synology NAS solution in 2022 is going to be smooth/unrestricted is going to be paramount. Once again, I found no limitations or hindrances in DSM 7.1 with the DS2422+ and drives I tested compared with the same operations using the Synology HAT5300 drives. Even directly in the app center itself, I was able to select the volume that had the 3rd party media as the default installation directory for all apps if I wanted, without any limitations or warning.

The improved resource monitor in DSM 7.1 also allowed full and unfettered monitoring of the full storage pools, volumes and individual drives as normal.

In the control panel, the shared folders that I created on the 3rd party drive built volume could still be added to the media indexing folders with zero restriction, limitations and without any notification or warning.

The same goes for using some of the background applications such as snapshots and replication used with the non-Synology drive volume. These services also had all of their more customizable features of retention, schedules and capacity available too.

Heading into more business’y territory, the Synology Virtual Machine Manager was still able to use the volume made of 3rd party drives as an available storage space, as well as accessible for VM images and services. The number of these larger-scale solutions from Synology that are deployed for VM utilization is growing rapidly as the tool improves (as well as used in conjunction with the likes of VMware, Hyper-V, SaaS and PaaS providers to sync/migrate from over time) so this was always going to be a crucial area of storage concern for many in DSM 7.1’s drive support.

Equally, there was no limitation to the individual configuration options that Synology VMM includes for the storage you connect it to.

You will also be pleased to hear that the full range of backup and synchronization tools that are included with Synology DSM 7.1 have unrestricted access to volumes made of 3rd party drive media. I tested Hyper Backup, Cloud Sync and Active Backup Suite – all three could utilize volumes, regardless of the drives in the pool, with equal features and services. I was unable to test Hybrid Share, but I saw no indication that this would have any limitation either.

Users looking to use the Synology storage as a direct target for ISCSI LUNs will also be pleased to hear that 3rd party drive built volumes worked 100% normally and there were zero warnings on screen.

Finally, Synology’s ever-evolving Surveillance station software had complete, unrestricted and no-warning access to the 3rd party HDD volumes and there was no hindrance whatsoever when connecting the service. The DS2422+ and large-scale solutions like it are always going to be popular with users who choose Synology for this CCTV software (those recordings can add up to terabytes in no time at all) and with Synology providing 16TB drives at max capacity in summer 2022 and the likes of WD and Seagate hitting 22TB right now, many users will want to know that 3rd party media in these systems is still viable.

Synology 2022/2023 Enterprise/Business NAS & 3rd Party HDD/SSDs – Conclusion

As mentioned in my introduction, I really did struggle to find anything on DSM 7.1 on the DS2422+ using 3rd party hard drives that were restricted or barred from use at all. There IS the ever-present amber warning on the system’s initial GUI splash screen, but there did not seem to be any restriction on the services and features of DSM 7.1. So, this leads to the question of support and also what makes the Synology branded media better choice for the end-user. For that first point, I reached out to Synology earlier in the year to ask for further clarification on how support would be provided by the brand with regard to system’s that are utilizing storage media that is certified/confirmed/present on the Synology Compatibility pages. Here was that response from back in Feb ’22:

We have always recommended only using the drives tested and verified by our engineers to ensure long-term system reliability many many years ago. While non-verified drives can still be used on all devices, the updated policy is being introduced on new products primarily purchased by our business and enterprise clients in an effort to highlight the potential issues with using them. The policy still allows for the use of non-verified drives but with certain restrictions, such as status indicators and alerts indicating the system is not in an officially supported configuration and certain drive metrics not being supported. At the same time we understand that there is room for improvements to the user experience while still ensuring our customers are aware of the issue. In an upcoming DSM update, we are adjusting the alert level shown and also adding drive S.M.A.R.T. monitoring for unverified drives.

So, it would look like the comments on multiple social message boards (Facebook, Reddit, Syno Forums, etc are at the very least being read), However, for many this message does not fully cover the question of detailing the level of support that the brand will indeed provide in the event of perfectly reasonable failure. I raised this matter with Synology with the following examples for guidance (as I felt they covered a cluster of existing scenarios posed by users online):

Example #1, a Synology DS3622xs+ or DS2422+ owner purchases their unit and 12 Seagate EXOs HDDs, then 36 months down the line they suffer an unexpected (but perfectly reasonable) PSU failure. Will the brand support this user and provide a replacement PSU?

Alternatively, Example #2, if the hardware failure (still within perfectly reasonable parameters of hardware that is mass-produced of course) is controller board based? Where will the utility of non-Synology media stand?

A senior Synology manager provided the following response and clarification:

When a customer makes a technical support request, our engineers will work with them in troubleshooting the cause of the issue and to find a solution to resolve it. If it is determined that a failure is directly attributable to a 3rd-party component that has not been validated by Synology, our engineers may make the decision to reject continuing the diagnostics process. This is carried out because in many cases, there is little that our engineers can do without having those exact components on hand to replicate the problem and then determine a way to workaround or mitigate them.

You can read the rest of that article and all the points it covered HERE – https://nascompares.com/2022/02/17/synology-nas-and-hard-drive-compatibility-in-2022-should-i-be-worried

On the subject of what makes Synology Drive media a recommended choice in Synology solutions, Synology was keen to highlight that:

  1. Better reliability: From our observation, our support tickets relating to HDD/SSD issues dropped 19% so far, which means users will gain better reliability with Synology HDDs.
  2. Enhanced performance: Performance when multiple devices read sequentially compared to 3 Party HDD +36%
  3. Seamless update: online HDD/SSD firmware update from DSM without downtime or rebuilding disk array

As further releases in the Synology 2022 range start to appear on the market (most recently the RS422+, RS822+ and DS1522+ at some point) we are seeing Synology’s position on Hard Drives in these less enterprise or large-scale solutions soften somewhat. listing many more HDD and SSDs from 3rd party brands (but still nowhere near as many as in previous NAS releases such as the DS920+ or DS1621+, with many glaring omissions from the likes of WD and Seagate, see here). Bottom line, it is always going to be the prerogative of Synology to choose the storage media they believe is in the best interest of the systems that provide, but I don’t think this is a subject that is going to be removed any time to everyone’s satisfaction. Right now you can definitely take advantage of pretty much the whole Synology DSM 7.1 features and services with your new high-end 2022/2023 Synology NAS purchase, but until more time passes and we have case examples of support queries running smoothly on forums such as Reddit of Synology’s official support forum, many will still have a lingering doubt about using 3rd party media on these systems. We will be doing more in-depth HDD comparisons with Synology media and 3rd party alternatives in the Synology DS2422+ very soon, so stay tuned and/or subscribe to hear about it first and once again thanks to CCLOnline for supplying us with the Synology NAS for our tests. Have a great week

 

📧 LET ME KNOW ABOUT NEW POSTS 🔔

Enter your email address to subscribe to this blog and receive notifications of new posts by email.

Join 1,263 other subscribers


Get an alert every time something gets added to this specific article!


Want to follow specific category?

This description contains links to Amazon. These links will take you to some of the products mentioned in today's content. As an Amazon Associate, I earn from qualifying purchases. Visit the NASCompares Deal Finder to find the best place to buy this device in your region, based on Service, Support and Reputation - Just Search for your NAS Drive in the Box Below

Need Advice on Data Storage from an Expert?

We want to keep the free advice on NASCompares FREE for as long as we can. Since this service started back in Jan '18, We have helped hundreds of users every month solve their storage woes, but we can only continue to do this with your support. So please do choose to buy at Amazon US and Amazon UK on the articles when buying to provide advert revenue support or to donate/support the site below. Finally, for free advice about your setup, just leave a message in the comments below here at NASCompares.com and we will get back to you. Need Help? Where possible (and where appropriate) please provide as much information about your requirements, as then I can arrange the best answer and solution to your needs. Do not worry about your e-mail address being required, it will NOT be used in a mailing list and will NOT be used in any way other than to respond to your enquiry. [contact-form-7] Terms and Conditions Alternatively, why not ask me on the ASK NASCompares forum, by clicking the button below. This is a community hub that serves as a place that I can answer your question, chew the fat, share new release information and even get corrections posted. I will always get around to answering ALL queries, but as a one-man operation, I cannot promise speed! So by sharing your query in the ASK NASCompares section below, you can get a better range of solutions and suggestions, alongside my own.  

Synology DSM 7.1 Beta Now Available to Download

23 février 2022 à 01:50

The Synology NAS DSM 7.1 Beta Software is Now Available to Download


Good news for anyone that wants to see how Synology DSM will improve in the coming months, with Synology today announcing the Beta release of DiskStation Manager 7.1, giving system admins a chance to test out the expanded functionality. DSM 7.1 builds further on the massive platform upgrade introduced with DSM 7.0 and introduces many innovative enhancements designed to address IT challenges.  “DSM 7.1 is an important evolution for one of the most widely used data management platforms in the industry,” System Product Management team manager Shamrock Ko said. “Building on the solid foundation we set with 7.0, we can now focus on addressing the more specific challenges that our customers identify during their day-to-day use of the platform.”


Highlights of Synology DSM 7.1 Available in the Beta

NAS Protection – Efficiently back up and restore all your configurations, applications, and data in DSM

Enhanced Storage – Improvements to our SSD cache implementation and new options to simplify SMB file server access

Flexible deployment – Solutions for heavy VM use, multi-site data protection, and domain management in non-trusted environments

Monitoring & Management – Gain better oversight of processes and statuses throughout your deployment with more information aggregated to your preferred DSM account

Package Refreshes – Be the first to benefit from the latest improvements in IT management, user experience, and security with new versions of our most-used applications

Improvements in Synology DSM 7.1


DSM 7.1 brings key improvements to the storage management experience. Starting with the introduction of file aggregation portals, it adds SMB DFS capability to enable administrators to link together multiple Synology systems, providing more convenient file access for end users by removing the need to remember separate addresses. The new user interface introduced in 7.0 has been further optimized by consolidating background tasks into an administrator-friendly overview that provides greater transparency into what is happening on the system, even across different user accounts. For Synology High Availability clusters, users can now view and manage drives on both systems from a single instance of Storage Manager for easier maintenance and management. On the performance side, DSM has long supported flash caching to boost random I/O performance cost-effectively. This new version will further economize SSD caching with the ability to speed up multiple storage volumes at the same time.


Full Synology NAS Backup in DSM 7.1

Back up not just the data on your Synology NAS, but all of your DSM settings, applications, and user details to another NAS with a powerful new feature in your favorite backup suite.

Improved Deployment Options in Synology DSM 7.1

New options help power users conquer complex scenarios, such as heavy VM use, multi-site data protection, and domain management in non-trusted environments.


Synology DSM 7.1 NAS System Protection


DSM 7.1 introduces complete, bare-metal level backups of the entire system. Powered by Synology Active Backup for Business, the ability to clone and replicate the entire Synology system greatly accelerates recovery time objectives (RTO) in the event of a total site failure. Full system restoration capability also introduces a quick and convenient way to deploy identically configured systems. 


Improvements in DSM 7.1 towards the Synology NAS Ecosystem


In tandem with DSM 7.1, Synology is launching several major enhancements to applications and services.

  • Active Backup for Business: bandwidth control, expanded monitoring and reporting capabilities, and support for DSM backups
  • Active Insight: centralized login activity monitoring and Hyper Backup task statuses
  • Synology C2 Hybrid Share: server-side snapshots for better file protection
  • Directory Server: support for read-only domain controllers to improve deployment security and flexibility
  • Synology Drive: revamped mobile user experience and improved monitoring/auditing capabilities
  • MailPlus: Virtual DSM support, expanded management options, importing and migration improvements
  • Virtual Machine Manager: storage I/O performance improvements and QoS capabilities

“Our constantly evolving DSM platform keeps adding capabilities to both new and existing deployments,” said Weili Lu, product manager for DSM. “The pre-release program provides a chance for us to work closely with our customers, providing early access to new features and obtaining valuable feedback in return.”


How to Access the Synology DSM 7.1 Beta Software?


DSM 7.1 Beta and companion applications and services will be available starting today as part of Synology’s pre-release program. Interested users are invited to install the pre-release software on non-production or virtualized systems. You can download the Synology DSM 7.1 Beta by clicking the button below to take you to the Synology download centre:



 

Limitations and Considerations of Testing the Synology DSM 7.1 Beta on your NAS


It is worth remembering that the Synology NAS DSM 7.1 Beta is exactly that, a beta. You should not consider installing this pre-release version of the software on your NAS it contains mission critical or personal irreplaceable data that is not backed up to at least two other locations. Below is a much more precise breakdown of what the DSM 7.1 beta includes, considerations you should factor in before utilizing it and which features have been added/changed in this new release:

  1. This beta software is for evaluation purposes only and should not be installed in production environments. Synology cannot be held responsible for any damage, such as accidental data loss, caused by this beta software.
  2. After installing this update, you will not be able to downgrade to a previous DSM version.
  3. This update will restart your Synology NAS.
  4. For the following models, DSM 7.1 will be the last upgradable version.
    • XS Series: RS3413xs+, RS10613xs+, RS3614xs+, RS3614xs, RS3614RPxs, RC18015xs+, DS3615xs, DS2015xs
    • Plus Series: DS2413+, DS1813+, DS1513+, DS713+, RS2414RP+, RS2414+, RS814RP+, RS814+, DS214+, RS815RP+, RS815+, DS2415+, DS1815+, DS1515+, DS415+, DS215+
    • Value Series: RS814, RS214, DS414, DS214, DS214play, DS114, RS815, DS1515, DS715, DS415play, DS115
    • J Series: DS213j, DS414slim, DS414j, DS214se, DS215j, DS115j, DS216se
  5. Adjusted the LED indicator for drives’ health status. When a drive’s health status is critical or failing, the indicator will show static orange.
  6. Windows 2000 domains are no longer supported.
  7. Removed the “Synchronize with an NTP server every time a domain user signs in” option for Domain/LDAP advanced settings. Users can configure the “Synchronize with NTP server” option at Regional Options > Time instead.
  8. Added support for the UPS power-off function at Control Panel > Hardware & Power > UPS.
  9. Synology Storage Replication Adapter can only be used with DSM 7.0.1 or earlier versions. If you are using or plan to use Synology Storage Replication Adapter, please continue to use the current DSM version.

What’s New in the Synology DSM 7.1 Beta:

  1. SSD Cache Groups can be allocated to multiple volumes, allowing for more flexible management of SSD cache capacity.
  2. Storage Manager now supports the management of the drives and storage of both active server and passive server in a Synology High Availability cluster.
  3. If there is a file system error, DSM will unmount the volume to run file system checks without interrupting the services on other volumes.
  4. Reduced the minimum threshold for low capacity notification from 5% to 3%.
  5. Added support for custom OIDC (OpenID Connect) settings to integrate DSM with external SSO servers.
  6. Added support for the RTF editor to allow users to preview notification message content and style in real-time when editing.
  7. Added support for bypass traverse checking at Control Panel > File Services > Advanced to allow users to traverse folders and access permitted files or subfolders.
  8. Supports specifying domains from the list of trusted domains to synchronize domain data.
  9. Added the Greenwich Mean Time (GMT+00:00) time zone option at Control Panel > Regional Options > Time.
  10. Added the synchronization status between DSM and NTP servers at Control Panel > Regional Options > Time.
  11. Added icons on the taskbar to indicate ongoing background tasks that might affect system performance.
  12. Users can now open tabs directly from search results in Control Panel.
  13. Supports automatically updating the domain database and syncing domain data regularly. For Synology NAS that are used to create domains, the “Update User Groups/Lists” option in Control Panel > Domains/LDAP will be disabled by default after updating to DSM 7.1 Beta.

 


📧 LET ME KNOW ABOUT NEW POSTS 🔔

Enter your email address to subscribe to this blog and receive notifications of new posts by email.

Join 1,460 other subscribers


Get an alert every time something gets added to this specific article!


Want to follow specific category?

This description contains links to Amazon. These links will take you to some of the products mentioned in today's content. As an Amazon Associate, I earn from qualifying purchases. Visit the NASCompares Deal Finder to find the best place to buy this device in your region, based on Service, Support and Reputation - Just Search for your NAS Drive in the Box Below


Other products mentioned on this article:  

SEARCH IN THE BOX BELOW FOR ANY OTHER NAS

Need Advice on Data Storage from an Expert?

We want to keep the free advice on NASCompares FREE for as long as we can. Since this service started back in Jan '18, We have helped hundreds of users every month solve their storage woes, but we can only continue to do this with your support. So please do choose to buy at Amazon US and Amazon UK on the articles when buying to provide advert revenue support or to donate/support the site below. Finally, for free advice about your setup, just leave a message in the comments below here at NASCompares.com and we will get back to you. Need Help? Where possible (and where appropriate) please provide as much information about your requirements, as then I can arrange the best answer and solution to your needs. Do not worry about your e-mail address being required, it will NOT be used in a mailing list and will NOT be used in any way other than to respond to your enquiry. [contact-form-7] Terms and Conditions Alternatively, why not ask me on the ASK NASCompares forum, by clicking the button below. This is a community hub that serves as a place that I can answer your question, chew the fat, share new release information and even get corrections posted. I will always get around to answering ALL queries, but as a one-man operation, I cannot promise speed! So by sharing your query in the ASK NASCompares section below, you can get a better range of solutions and suggestions, alongside my own.  

How to Install Plex on a Synology NAS with DSM 7

7 février 2022 à 01:11

A Guide to Installing Plex Media Server on your Synology NAS with the DSM 7

If you have been looking at buying a NAS drive for Plex to use as your own private Netflix, then there is a very good chance that you have heard the name ‘Synology’. They are the brand that produces some of the most user-friendly, yet powerfully efficient (yes, that is a thing!) servers in the market in 2022 and are often a highly recommended choice for setting up a slick, polished media streaming solution that uses YOUR movies/boxsets. Last year, Synology updated its system software and services platform, Diskstation Manager, from version 6.2 to 7.0 and improved a number of the system’s abilities and processes. However, the process for installing Plex media server on your Synology NAS changed, with DSM changing access privileges and defaults for 3rd party programs in order to ensure their solutions were as secure as possible. If you are running a Synology NAS drive with DSM 6.2 and are wondering how to install Plex Media Server, it is still remarkably straight forward and a full video walkthrough guide on this can be found HERE. However, those of you who have the most recent DSM7 upgrade (with DSM 7.01 and 7.1 already rolling out over 2022 gradually) will have found that the process for installing Plex has changed noticeably. So, today I wanted to walk you through, step by step, how to install Plex on a DSM 7 Synology NAS from beginning to end and ensure you get it right, first time. Alternatively, there is a video at the bottom of the page that will walk you through even quicker. Thanks for reading and I hope you enjoy this guide.

Plex Installation Guide on the DSM 7.0

Installing Plex on a NAS with DSM 7.0 is actually VERY similar to that of installing it on a DSM 6.2 Synology NAS, however, there are a few small changes in the process which allow Plex Media Server to access the correct directories. Previously these steps might be needed by most people but were not directed by the application especially clearly, so having these steps integrated into the formal setup is actually quite a smart idea by Synology. Let’s begin:

Step 1 – Head To The App Center

Step 2 – Go to the Beta Section

Step 3 – Find Plex Media Server and select Join Beta

Step 4 – Install Beta Application (speed depends on Internet Connection)

Step 5 – Select the location of where the Log Files will be installed – Can be left blank and it will save to the default directory

Step 6 – (This is the NEW bit) Give the Plex Media Server Application Permission to access the media directories. Head to the Control Panel

Step 7 – Then ‘Shared Folders’

Step 8 – Select the Folder where your Media is located in. In my case it is DS220PLUSSHARE – But it will be different on your own NAS device and based on your own storage setup

Step 9 – Select EDIT (at the top)

Step 10 – Then select the Permissions Tab

Step 11 – If Plex has created a local User (likely in DSM 6.2 . DSM 6 7.0 migration setups), make sure that the PLEX user account still has Read and/or Read/Write Access in the tick box list

Step 12 – Then (IMPORTANT) Select the drop-down menu at the top and switch to ‘System Internal’

Step 13 – Scroll down to the ‘Plex’ entry and give it Read and Write Access, then save the changes

Step 14 – Head back into the App Center window and click OK on the Plex Media App install setup window

Step 15 – The Plex Media APP should be installed and you can go ahead and click OPEN in the App Center window OR open it from the main Synology App dashboard

Step 16 – As this is a reinstallation of Plex Media Server on a NAS system as far as the Plex NAS app is concerned, the system may require PLEX to ‘claim’ the NAS once again, just head into the individual Server Settings and an option to CLAIM the server will appear in orange

Step 17 – Whether this is your first Plex Installation OR a DSM migration, you will likely need to establish the pathways for each multimedia file type.

Step 18 – Just head upto the ADD LIBRARY option and a popup will appear that allows you to select each Media Type

Step 19 – Then browse the directories (that you gave the Plex Media Application permission to access) and add the media that is appropriate

Step 20 – Now the Plex Media Server Application will scrape all the metadata from the site librarys (rotten tomatoes, IMDB, etc) and fill out all the slick PLEX GUI for your connected clients to enjoy.

And there you have it. Plex is now installed on your DSM 7 equipped NAS System. Here is a video that will guide you through the process if you prefer visuals over text!

Want to learn more about DSM 7.1 and what Synology plan for 2022? Watch my article below that covers the highlights:

 

If you are looking for the driver fix for the Synology NAS and Plex installation with J4025 and J4125 processors, you can find the video walkthrough and step by step guide below:

 

📧 LET ME KNOW ABOUT NEW POSTS 🔔

Enter your email address to subscribe to this blog and receive notifications of new posts by email.

Join 1,457 other subscribers


Get an alert every time something gets added to this specific article!


Want to follow specific category?

This description contains links to Amazon. These links will take you to some of the products mentioned in today's content. As an Amazon Associate, I earn from qualifying purchases. Visit the NASCompares Deal Finder to find the best place to buy this device in your region, based on Service, Support and Reputation - Just Search for your NAS Drive in the Box Below

 

SEARCH IN THE BOX BELOW FOR ANY OTHER NAS

Need Advice on Data Storage from an Expert?

We want to keep the free advice on NASCompares FREE for as long as we can. Since this service started back in Jan '18, We have helped hundreds of users every month solve their storage woes, but we can only continue to do this with your support. So please do choose to buy at Amazon US and Amazon UK on the articles when buying to provide advert revenue support or to donate/support the site below. Finally, for free advice about your setup, just leave a message in the comments below here at NASCompares.com and we will get back to you. Need Help? Where possible (and where appropriate) please provide as much information about your requirements, as then I can arrange the best answer and solution to your needs. Do not worry about your e-mail address being required, it will NOT be used in a mailing list and will NOT be used in any way other than to respond to your enquiry. [contact-form-7] Terms and Conditions Alternatively, why not ask me on the ASK NASCompares forum, by clicking the button below. This is a community hub that serves as a place that I can answer your question, chew the fat, share new release information and even get corrections posted. I will always get around to answering ALL queries, but as a one-man operation, I cannot promise speed! So by sharing your query in the ASK NASCompares section below, you can get a better range of solutions and suggestions, alongside my own.  

Synology DSM 7.1 – Features & Services Revealed

3 décembre 2021 à 00:03

Information on Synology DSM 7.1 Revealed During the Synology 2022 Event

An interesting part of Synology’ recent keynote speech, during the brand’s ‘2022 and Beyond’ event that did not get anywhere near the attention it deserved, was the details that were shared on DSM 7.1 and numerous individual applications and services that will see improvements in this next sub-update to DSM. Although the bulk of these improvements largely target the enterprise and high-end business sector, many of them demonstrate a large degree of focus being given to recovery of data, ease of access and scalability within the Synology platform in the future. The leveraging of Synology C2 against the majority of these features (as well as cloud linked services such as Active Insight) likely means that a few of these will directly/inadvertently run into subscription services, but nevertheless, it is interesting to see where Synology is headed in their next update.

Synology DSM 7.1 and Improvements in the Features, Actions and GUI of Active Insight

Synology DSM 7.1 will be improving the ability to overview and control multiple storage areas at once, from bare metal to those on the C2 platform. A big part of this is going to be improvements in the Active insight, a tool that already gives users a lot of control of multi-site setups. This user interface will be tweaked and improved to make these controls (such as pushing updates across the whole storage network and monitoring areas of concern/improvement).

Additionally, there will be updates in how Active insight deals with suspicious activity in connected users. Using existing historical data in usage patterns, locations and behaviour, it can report suspicious behaviour to the admin user and allow much faster recognition of troubling access behaviour – eliminating infiltration of your storage system even more. This information will be presented to eligible admin users with significant geolocational data, a breakdown of suspicious connectivity and suggestions of how to proceed.

Another improvement that will be rolled into Active Insight in DSM 7.1 is the integration of Hyper Backup monitoring and control from within it’s GUI. This will allow the success/failure/issues of existing backup routines from within DSM 7.1 on one or more NAS servers to be monitored, actioned or configured via the single portal access point of Active Insight. The extent to which this will be available is still yet to be fully confirmed, but it promises to be the first of many staple DSM applications that will be integrated into Active Insight in DSM 7.1 and onwards.

Active insight is still primarily a higher-end business and Enterprise subscription platform, so it’s improvements in DSM 7.1 will only really be felt in the highest tiers, but it is still nice to see it implementing already commonly asked features in the next sub-release of DSM.

Synology DSM 7.1 and Hybrid Share improvements Adding GFS & Cache Warm-Up

The Synology Hybrid Share service (introduced in DSM 7.0) allows users to connect their NAS service with an area of C2 cloud storage, which can be locally cached based on access. Hybrid Share was always promoted as an ideal means for users to have secure, yet convenient access to their storage, as well as allowing a multi-site setup to synchronize remotely a great deal more easily. DSM 7.1 will see HybridShare improved with several new features that will include HTTP/3 support, support of GFS (Global File System) and a new cache warm-up feature.

GFS has the added benefit of preventing multiple users from editing the same file and (upon saving) creating multiple versions of a file with their own respective edits. With GFS the file is locked to a user accessing via the share, ensuring that all other connected users who try to access that file are notified that it is in use/locked. The addition of HTTP/3 support will improve performance during access (something already integrated on other cloud-only platforms for responsiveness of files live). Finally, there is improvements in how local caching of the C2 Clous storage is handled. The cache warmup is an advanced version of the existing cache feature. Currently, in Hybrid Share, when a file is accessed, it will likely be cached for an indefinite period and eventually flushed as further files are accessed over time. The cache warm-up feature will see/learn which files are more commonly accessed and have them loaded in.

Further Roll out of Out of Band Management

For those that are not aware, Out of Band Management (OOB or OOBM) connection is a secure and alternative means for admins to connect with a server to access important log information (in order to facilitate a repair or restore) as well as allow administrators to utilize higher power controls for restoration, power cycling, rebooting or simply for troubleshooting.

Synology will be rolling out the support of an out of band physical port in future hardware releases and this should assist in reducing downtime and the need for maintenance admins to be physically on-site.

Improved Multi-Server, Multi-File System via a Single Portal coming in DSM 7.1

Synology DSM 7 already improved directory services and different file servers. It is not uncommon for a business to feature several different file server types in their environment (whether that is for suitability to other services in house or for reasons of performance). DSM 7.1 is planned to have support for a global folder (i.e single all accessing) that can see and access the file server directories inside and allow much more convenient interaction for users, via a single portal access point. This will be DSM 7.1 providing DFS (Distributed File System) over SMB for convenience.

Improvements in Remote Domain Controller Support

DSM 7.0 has already integrated secondary domain controller support for reasons such as load balancing and improving the availability of storage across multiple sites. DSM 7.1 will add to this with the support of Read-Only domain controllers. Ultimately this will allow businesses to create a further storage point/node to their storage network but reducing the risk to the greater system if access is being made by a less wholly secure environment.

Complete DSM Backup and Restoration from Synology C2 in DSM 7.1

Synology already features numerous methods of backup and restoration in DSM 7.0 (and indeed DSM 6.2 before it). Key applications that cover the NAS data, your local machine data and even local cached C2 cloud data are supported and/or can be utilized in Active Backup Suite, Hyper Backup, Synology Drive and Snapshot Replication to create backups and restore when necessary. Alongside this, features such as encryption, compression or deduplication are available to allow further backup opportunities and further improve the likelihood of recovering your data. However, all of these are targetted at individual shared folders, storage volumes or your local client machine – not the NAS, complete data layout and its entire system configuration. That is where DSM 7.1 is going to improve things with FULL DSM Backup – the entire NAS architecture, configuration and digital layout as a whole, comprehensive backup (almost certainly to Synology C2). Although details were a little thin on the ground, existing features of the existing backup/restoration apps in DSM 7 (such as deduplication, incremental backups, scheduling, custom retention policies and fast replication) will be supported in the FULL DSM Backup service.

Synology and Scale-Out Storage Solutions in the Future

Aside from the details regarding how DSM 7.1 is shaping up, there was also a brief period at the end of the keynote video that highlighted something that Synology is working on in future developments. Moving beyond their existing scale-up solutions (ie bare metal solutions that can have a # of expansions added for further Terabytes and Petabytes of storage), currently they are examining the implementation of whole storage systems (made up of multiple physical servers) that feature a distributed file server layer. This would allow the equivalent of a local RAID to become whole systems being synchronized together. This would allow connected clients to only interact with a single interface as usual and a whole system/node going online resulting in zero difference being felt. That also would theoretically mean that changes to the system and its hardware would be frictionless to constant access and added further storage hardware (i.e more bare metal nodes) would also be considerably easier (see gif below).

There were further improvements highlighted in the keynote Synology 2022 speeches, but these are all largely going to be rolled out in DSM 7.0 in the first half of the year. These include improvements to the Synology Drive Mobile Application and UI, MacOS support, SRM 1.3, Surveillance Station 9.0 and much more. Expect full coverage of those here on NASCompares and over on my YouTube channel here soon. Don’t forget to subscribe!

 


Articles Get Updated Regularly - Get an alert every time something gets added to this page!


This description contains links to Amazon. These links will take you to some of the products mentioned in today's content. As an Amazon Associate, I earn from qualifying purchases. Visit the NASCompares Deal Finder to find the best place to buy this device in your region, based on Service, Support and Reputation - Just Search for your NAS Drive in the Box Below

 

SEARCH IN THE BOX BELOW FOR NAS DEALS

Need Advice on Data Storage from an Expert?

We want to keep the free advice on NASCompares FREE for as long as we can. Since this service started back in Jan '18, We have helped hundreds of users every month solve their storage woes, but we can only continue to do this with your support. So please do choose to buy at Amazon US and Amazon UK on the articles when buying to provide advert revenue support or to donate/support the site below. Finally, for free advice about your setup, just leave a message in the comments below here at NASCompares.com and we will get back to you. Need Help? Where possible (and where appropriate) please provide as much information about your requirements, as then I can arrange the best answer and solution to your needs. Do not worry about your e-mail address being required, it will NOT be used in a mailing list and will NOT be used in any way other than to respond to your enquiry. [contact-form-7] Terms and Conditions Alternatively, why not ask me on the ASK NASCompares forum, by clicking the button below. This is a community hub that serves as a place that I can answer your question, chew the fat, share new release information and even get corrections posted. I will always get around to answering ALL queries, but as a one-man operation, I cannot promise speed! So by sharing your query in the ASK NASCompares section below, you can get a better range of solutions and suggestions, alongside my own.  
❌