UniFi MASSIVELY Scale up their NAS Portfolio with the UNAS Pro 8, UNAS Pro 4, UNAS 4 and UNAS 2

Note, the UNAS Pro 2 is NOW LIVE on the UniFi Store . The UNAS 4, UNAS Pro 4 and UNAS Pro 8 are now in the site, but are not available till October.

Ubiquiti is preparing to significantly broaden its NAS product line in late 2025 with the introduction of four new systems under the UNAS branding. The new lineup follows the launch of the original UNAS Pro in 2024, which gained attention as a low-cost, seven-bay rackmount appliance that introduced UniFi into the NAS sector. With the release of the UNAS 2, UNAS 4, UNAS Pro 4, and UNAS Pro 8, the company is moving into what it describes as its “phase two” of NAS development, aiming to cover both desktop and rackmount form factors while integrating closely with the wider UniFi ecosystem. This expansion arrives at a time when established NAS vendors are tightening drive compatibility and raising prices, leaving a gap for alternatives that emphasise affordability, simplified deployment, and ecosystem consistency.

The UNAS Pro 8 NAS

4-Core ARM, 16GB RAM, 3x 10GbE, 8x SATA Bays, 2x M.2 Bays (trays required), Redundant PSU (2nd Sold Seperately) $799 – HERE

The UNAS Pro 8 will serve as the top-end model of the range, positioned in a 2U rackmount chassis and built to deliver higher capacity and redundancy. It features eight front-facing 2.5″/3.5″ SATA bays alongside two rear-mounted M.2 NVMe slots, accessible through modular trays.

The Pro 8 is powered by a quad-core ARM Cortex-A57 processor running at 1.7 GHz and paired with 16 GB of LPDDR4 memory. Unlike many entry-level ARM systems, the Pro 8 includes three 10-gigabit network interfaces: two SFP+ and one RJ45 supporting multi-gig speeds down to 100 MbE. Redundant hot-swappable 550W PSUs are supported, though only one is included by default, with seamless failover tested successfully under load.

Category	Specification
Form Factor	Rackmount NAS (2U)
Dimensions	442.4 x 480 x 87.4 mm (44.24 x 48.0 x 8.74 cm)
Weight	11.5 kg (25.35 lb)
Enclosure Material	SGCC steel
Mounting	Rack rails included
Drive Bays	8 x 2.5″/3.5″ SATA HDD/SSD
M.2 Support	2 x M.2 NVMe slots (2280/22110) via rear tray modules (sold separately)
RAID Support	RAID 0, 1, 5, 6, clustered RAID, Single Disk
Hot Swap	Supported
Max Drive Capacity	Tested up to 30 TB HDDs; UniFi-branded and third-party drives supported
CPU	Quad-Core ARM Cortex-A57, 1.7 GHz
Memory	16 GB LPDDR4 (non-upgradeable)
System Storage	~25.2 GB internal flash (likely 32 GB with over-provisioning)
Network Interfaces	2 x 10G SFP+, 1 x 10GbE RJ45 (multi-gig fallback to 5G/2.5G/1G/100M)
USB / Expansion	None
Power Method	Dual PSU bays, hot-swappable modules
Power Supply	2 x 550W AC/DC hot-swappable PSUs (1 included by default)
Max Power Budget	175W for drives
Max Consumption	200W
Cooling	Multiple system fans with active fan control
Management	UniFi OS web interface; Ethernet, Bluetooth 4.1 for setup
Software File System	Btrfs with snapshot support
Certifications	FCC, CE, IC; NDAA Compliant

The system uses SGCC steel for the enclosure, weighs 11.5 kg, and includes rack rails in the box, a detail rarely seen in turnkey solutions. Performance tests have demonstrated sequential reads close to 850 MB/s on HDDs in RAID 5, with expectations of saturating a 10GbE link when using SSDs or RAID 0.

The UNAS 2 NAS

4-Core ARM, 4GB RAM, 1X 2.5GbE PoE+++, 2x SATA Bays, Power Over Ethernet delivery (PoE+++ Adapter Included) $199 – HERE

At the opposite end of the spectrum is the UNAS 2, UniFi’s smallest NAS to date. This desktop unit measures just 13.5 x 12.9 x 22.37 cm and weighs 1.3 kg, with a polycarbonate chassis designed to keep cost and weight down.

The device supports two 3.5″ SATA drives housed in a shared tray, a design that requires both drives to be removed together and does not permit hot-swapping. This approach raises concerns about handling healthy drives during replacement but reduces the mechanical complexity of the system.

Category	Specification
Form Factor	Desktop NAS
Dimensions	135 x 129 x 223.7 mm (13.5 x 12.9 x 22.37 cm)
Weight	1.3 kg (2.85 lb)
Enclosure Material	Polycarbonate
Drive Bays	2 x 3.5″ SATA HDD
RAID Support	RAID 0, RAID 1, Single Disk
Hot Swap	Not supported (shared tray for both drives)
Max Drive Capacity	Confirmed support up to 30 TB HDDs
CPU	Quad-Core ARM Cortex-A55, 1.7 GHz
Memory	4 GB LPDDR4 (non-upgradeable)
System Storage	Internal flash for operating system
Network Interface	1 x 2.5 GbE RJ45 (PoE++ power + data)
USB Ports	1 x USB-C (5 Gbps, storage devices only)
Power Method	PoE++ (via 2.5 GbE port)
Power Supply	60W PoE++ injector included
Max Power Budget	52W for drives, 60W maximum system consumption
Cooling	Rear cooling fan with bottom intake vents, software fan control
Display	1.47″ colour LCM (status only, non-touch)
Noise Levels	~31–32 dBA idle, up to ~38 dBA under load
Thermal Range	CPU ~75–80°C under stress, 50–60°C idle/light use
Management	UniFi OS web interface, Ethernet, Bluetooth 4.1 for setup
Certifications	FCC, CE, IC; NDAA Compliant

The UNAS 2 runs on a quad-core ARM Cortex-A55 at 1.7 GHz with 4 GB of LPDDR4 memory. Networking is provided by a single 2.5 GbE RJ45 port, which also delivers PoE++ power, with a maximum system budget of 60W (52W for drives). A 60W PoE++ injector is included for users without a suitable switch. A 1.47-inch colour LCM display on the front provides status updates, though it is non-interactive. A USB-C port rated at 5 Gbps adds external storage capability, addressing an omission noted in the original UNAS Pro, but it does not support UPS integration or networking adapters.

The UNAS Pro 4 NAS

4-Core ARM, 16GB RAM, 10GbE, 4x SATA Bays, 2x M.2 Bays (trays required), Redundant PSU (2nd Sold Seperately) $499 – HERE

Between these two extremes sits the UNAS Pro 4, a 1U rackmount unit designed for users who want the resilience of redundant PSUs and NVMe support without committing to an eight-bay chassis.

It includes four SATA bays and two M.2 NVMe slots, sharing the same ARM Cortex-A57 CPU and 16 GB of memory as the Pro 8. Like its larger counterpart, it is built for rack environments where redundancy and compact form factor are key priorities.

While exact dimensions and weight have not yet been confirmed (with the UNAS 2 and UNAS Pro 8 being the main focus of this new launch), the design is expected to follow Ubiquiti’s established rackmount conventions. Its specification profile makes it an option for smaller businesses or branch offices that need rack integration but do not require the capacity of an eight-bay system.

Category	Specification
Form Factor	Rackmount NAS (1U)
Drive Bays	4 x 2.5″/3.5″ SATA HDD/SSD
M.2 Support	2 x M.2 NVMe slots
RAID Support	RAID 0, 1, 5, 6, clustered RAID, Single Disk
Hot Swap	Supported
CPU	Quad-Core ARM Cortex-A57, 1.7 GHz
Memory	16 GB LPDDR4 (non-upgradeable)
System Storage	Internal flash for operating system
Network Interfaces	Expected 2 x 10G SFP+, 1 x 10GbE RJ45 (matching UNAS Pro 8, TBC)
Power Method	Dual PSU bays, hot-swappable modules
Power Supply	2 x hot-swappable AC/DC PSUs (1 included by default)
Cooling	Multiple system fans with front-to-rear airflow
Management	UniFi OS web interface; Ethernet, Bluetooth 4.1 for setup
Positioning	Compact 1U rackmount, same CPU/RAM as Pro 8, with redundancy support

The UNAS 4 NAS

4-Core ARM, 4GB RAM, 1X 2.5GbE PoE+++ (TBC), 4x SATA Bays, 2x M.2 Bays (trays required), Power Over Ethernet delivery (PoE+++ Adapter Included) $379 – HERE

The UNAS 4, meanwhile, extends the desktop line and mirrors the design philosophy of the UNAS 2 but doubles the bay count.

It provides four 3.5″ SATA bays along with two M.2 slots, making it the only desktop model in the range to support NVMe caching or tiered storage.

It retains the same ARM Cortex-A55 CPU and 4 GB of fixed memory as the UNAS 2, positioning it as a modest but slightly more versatile desktop option.

Like the smaller model, it uses PoE+++ for power delivery and 2.5 GbE for connectivity, though it remains unconfirmed whether it will also include a secondary network interface for failover or link aggregation. As with other desktop models, the chassis is constructed from polycarbonate, with compact dimensions intended for office or home use rather than data centre deployment.

Category	Specification
Form Factor	Desktop NAS
Enclosure Material	Polycarbonate
Drive Bays	4 x 3.5″ SATA HDD
M.2 Support	2 x M.2 NVMe slots (for caching/tiered storage)
RAID Support	RAID 0, 1, 5 (dependent on bay usage)
Hot Swap	Not confirmed (likely similar tray design to UNAS 2)
CPU	Quad-Core ARM Cortex-A55, 1.7 GHz
Memory	4 GB LPDDR4 (non-upgradeable)
Network Interface	1 x 2.5 GbE RJ45 (PoE+++ power + data), possible secondary port (TBC)
USB Ports	1 x USB-C (5 Gbps, storage devices only)
Power Method	PoE+++
System Storage	Internal flash for operating system
Cooling	Rear fan with bottom intake, adjustable via UniFi OS
Management	UniFi OS web interface, Ethernet, Bluetooth 4.1 for setup
Positioning	Desktop equivalent to UNAS 2, scaled up with four bays and M.2 support

UniFi Drive 3.3 Update?

Alongside the hardware announcements, UniFi will also release UniFi Drive 3.3, a major update to its NAS management software.

This version introduces expanded RAID configuration options, broader support for third-party cloud platforms, enhanced fan control, and improved analytical tools for monitoring system health and performance.

Snapshots and backups remain central features, with cloud and LAN targets supported, while the update also improves scheduling flexibility and introduces additional reporting features.

Although iSCSI remains absent, UniFi Drive continues to mature from the limited platform released with the first UNAS Pro, and the 3.3 update is expected to improve usability across the entire new range.

The introduction of these four models demonstrates Ubiquiti’s intent to build a full family of NAS solutions rather than rely on a single experimental release. By offering both rackmount and desktop systems at varying capacities, the company is positioning itself to compete more directly with established NAS vendors, albeit with a more streamlined and ecosystem-focused approach. The UNAS 2 and UNAS 4 are targeted primarily at existing UniFi users seeking simple storage that integrates seamlessly with PoE switches, while the Pro 4 and Pro 8 are built to appeal to businesses looking for redundancy, higher bay counts, and greater throughput. The use of ARM processors across the line reflects UniFi’s efficiency-first design, even though it places limits on heavy workloads such as virtualisation or multimedia transcoding.

Detailed performance reviews and comparisons of the new models are expected in the weeks ahead, assessing how each device performs within its target segment. Particular attention will focus on how the Pro units handle sustained 10GbE workloads with HDD and SSD configurations, how the PoE-driven desktop models cope with thermal and power constraints, and how UniFi Drive 3.3 stacks up against more mature operating systems. With Ubiquiti steadily fleshing out its NAS portfolio one year on from the first UNAS Pro, the company’s ability to deliver consistent updates and address early hardware and software limitations will determine whether it can establish a lasting position in the NAS market.

Feature	UNAS Pro (2024)	UNAS 2	UNAS 4	UNAS Pro 4	UNAS Pro 8
Price	$499	$199	$379	$499	$799
Form Factor	Rackmount (2U)	Desktop	Desktop	Rackmount (1U)	Rackmount (2U)
Dimensions	Not confirmed	135 x 129 x 223.7 mm (13.5 x 12.9 x 22.37 cm)	TBC (similar scale, polycarbonate)	TBC (compact 1U rack)	442.4 x 480 x 87.4 mm (44.24 x 48.0 x 8.74 cm)
Weight	Not confirmed	1.3 kg	TBC (slightly heavier than UNAS 2)	TBC	11.5 kg
Enclosure Material	Metal (likely steel)	Polycarbonate	Polycarbonate	SGCC steel	SGCC steel
Drive Bays	7 x 2.5″/3.5″ SATA	2 x 3.5″ SATA	4 x 3.5″ SATA	4 x 2.5″/3.5″ SATA	8 x 2.5″/3.5″ SATA
M.2 NVMe Support	None	None	2 x M.2 NVMe	2 x M.2 NVMe	2 x M.2 NVMe
Hot Swap	Supported	Not supported (shared tray)	Likely limited (TBC)	Supported	Supported
Max Drive Capacity	> 20 TB confirmed	Up to 30 TB confirmed	Up to 30 TB expected	Up to 30 TB expected	Up to 30 TB confirmed
CPU	Quad-Core ARM Cortex-A57, 1.7 GHz	Quad-Core ARM Cortex-A55, 1.7 GHz	Quad-Core ARM Cortex-A55, 1.7 GHz	Quad-Core ARM Cortex-A57, 1.7 GHz	Quad-Core ARM Cortex-A57, 1.7 GHz
Memory	8 GB (early models)	4 GB LPDDR4 (non-upgradeable)	4 GB LPDDR4 (non-upgradeable)	16 GB LPDDR4 (non-upgradeable)	16 GB LPDDR4 (non-upgradeable)
System Storage	Internal flash (size not disclosed)	Internal flash	Internal flash	Internal flash	~25.2 GB internal flash (likely 32 GB with OP)
Network Interfaces	1 x 10GbE RJ45 (front-mounted)	1 x 2.5 GbE RJ45 (PoE++)	1 x 2.5 GbE RJ45 (PoE+++), possible 2nd port (TBC)	Expected: 2 x 10G SFP+, 1 x 10GbE RJ45	2 x 10G SFP+, 1 x 10GbE RJ45
USB Ports	None	1 x USB-C (5 Gbps, storage only)	1 x USB-C (5 Gbps, storage only)	None	None
Power Method	AC PSU (non-redundant)	PoE++ (via 2.5 GbE)	PoE+++	Dual PSU bays (hot-swappable)	Dual PSU bays (hot-swappable)
Power Supply	Integrated AC PSU	60W PoE++ injector included	PoE+++ injector/switch required	2 x hot-swappable PSUs (1 included)	2 x 550W hot-swappable PSUs (1 included)
Max Power Budget	Not published	52W for drives, 60W total	TBC (expected ~80–100W)	~150W (TBC)	175W for drives, 200W total
Cooling	Passive vents + fans, limited fan control (later patched)	Rear fan, bottom vents, fan control via OS	Rear fan with bottom intake, fan control	Front-to-rear airflow, multiple fans	Front-to-rear airflow, multiple fans
Display	Small LCD panel with system info	1.47″ colour LCM (status only)	TBC (likely same as UNAS 2)	None	None
Noise Levels	Moderate (rackmount fans)	~31–32 dBA idle, up to ~38 dBA load	Slightly higher than UNAS 2 (TBC)	Typical 1U fan noise	Adjustable, depends on drive/fan profile
Thermal Range	CPU ~70–80°C under load	CPU ~75–80°C stress, ~50–60°C idle	Similar to UNAS 2 (TBC)	~70–80°C CPU under load	CPU ~74–80°C, drives 38–47°C
Management	UniFi OS web interface, Ethernet	UniFi OS web interface, Ethernet, Bluetooth 4.1	UniFi OS web interface, Ethernet, Bluetooth 4.1	UniFi OS web interface, Ethernet, Bluetooth 4.1	UniFi OS web interface, Ethernet, Bluetooth 4.1
Software File System	Btrfs, snapshots (basic)	Btrfs, snapshots, backups	Btrfs, snapshots, backups	Btrfs, snapshots, clustered RAID	Btrfs, snapshots, clustered RAID
Certifications	FCC, CE (NDAA not confirmed)	FCC, CE, IC; NDAA compliant	FCC, CE, IC; NDAA compliant	FCC, CE, IC; NDAA compliant	FCC, CE, IC; NDAA compliant

SUBSCRIBE TO OUR NEWSLETTER
[contact-form-7]
Join Inner Circle

This description contains links to Amazon. These links will take you to some of the products mentioned in today's content. As an Amazon Associate, I earn from qualifying purchases. Visit the NASCompares Deal Finder to find the best place to buy this device in your region, based on Service, Support and Reputation - Just Search for your NAS Drive in the Box Below

Need Advice on Data Storage from an Expert?

Finally, for free advice about your setup, just leave a message in the comments below here at NASCompares.com and we will get back to you. Need Help? Where possible (and where appropriate) please provide as much information about your requirements, as then I can arrange the best answer and solution to your needs. Do not worry about your e-mail address being required, it will NOT be used in a mailing list and will NOT be used in any way other than to respond to your enquiry. [contact-form-7] TRY CHAT Terms and Conditions   Alternatively, why not ask me on the ASK NASCompares forum, by clicking the button below. This is a community hub that serves as a place that I can answer your question, chew the fat, share new release information and even get corrections posted. I will always get around to answering ALL queries, but as a one-man operation, I cannot promise speed! So by sharing your query in the ASK NASCompares section below, you can get a better range of solutions and suggestions, alongside my own.

WE LOVE COFFEE

 

Après l’UNAS Pro lancé en octobre 2024, UniFi vient d’annoncer 4 nouveaux modèles de NAS : UNAS 2, UNAS 4, UNAS 4 Pro et UNAS 8 Pro. Que vous soyez un particulier ou une PME, chaque modèle a été conçu pour répondre à des usages précis, « sans compromis sur la simplicité ni sur la performance » selon le fabricant.

UNAS 2 : la simplicité avant tout

Premier modèle de la gamme, l’UNAS 2 est un NAS 2 baies pensé pour ceux qui recherchent un appareil compact, facile à installer et performant. Son design épuré (qui rappellera les produits Apple) et son installation via un seul câble PoE++ en font une solution idéale pour un bureau ou un usage domestique.

Ce NAS est construit autour d’un processeur quad core ARM Cortex A55 cadencé à 1.7 GHz et épaulé par 4 Go de mémoire vive.

 

Caractéristiques principales :

• 2 baies pour disques durs ;
• processeur Quand Core ARM Cortex-A55 cadencé à 1,7 GHz ;
• 4 Go de mémoire vive ;
• 1 port réseau 2,5 Gb/s ;
• connectique USB-C en façade ;
• écran tactile intégré ;
• disponible en deux coloris.

L’accès aux disques se fait par le dessous du boîtier, tandis que l’alimentation et le réseau passent par un unique câble RJ45. Un injecteur PoE 60 W est fourni. UniFi propose également des disques durs maison (1, 8, 16 et 24 To).

Son prix : 214,80€ TTC.

UNAS 4 : plus de stockage et toujours aussi simple

L’UNAS 4 reprend les atouts du UNAS 2 tout en doublant les possibilités de stockage. Il propose 4 baies pour disques durs et 2 emplacements SSD NVMe pour le cache.

Le modèle n’est pas encore disponible mais son lancement est prévu avant la fin de l’année 2025. Son prix : 408€ TTC.

UNAS Pro 4 et Pro 8 : la gamme professionnelle

La série Pro s’adresse clairement aux entreprises et aux infrastructures IT. Ces modèles rackables misent « sur la puissance, la résilience et la flexibilité » selon le fabricant.

Points clés :

• 4 baies (UNAS 4 Pro) ou 8 baies (UNAS 8 Pro) ;
• processeur Quad Core ARM Cortex-A57 à 2 GHz ;
• 8 Go de RAM (UNAS 4 Pro)  ou 16 Go (UNAS 8 Pro) ;
• 2 emplacements SSD NVMe pour le cache ;
• 2 ports 10 Gb/s SFP+ et 1 port 10 Gb/s RJ45 avec MC-LAG ;
• alimentation redondante (UNAS 8 Pro).

L’UNAS Pro 8 est conçu pour les charges de travail intensives, tandis que l’UNAS Pro 4 reprend la même puissance dans un format rackmount 1U compact.

Prix et disponibilité :

• UNAS Pro 8 : sortie prévue en octobre 2025, 862,80€ TTC ;
• UNAS Pro 4 : attendu fin 2025, 538,80€ TTC.

UniFi Drive : le logiciel qui unifie l’expérience

Tous les modèles UNAS reposent sur UniFi Drive, qui évolue avec les besoins utilisateurs. Ses intégrations cloud (AWS S3, Backblaze B2, Wasabi), son support Active Directory et ses modes de refroidissement personnalisables en font un atout majeur.

En syntèse

Avec cette nouvelle gamme, UniFi propose une offre de stockage claire et évolutive, couvrant les besoins des particuliers comme ceux des entreprises :

• UNAS 2 : simplicité et compacité pour un usage domestique ;
• UNAS 4 : plus de capacité sans complexité supplémentaire ;
• UNAS Pro 4 & Pro 8 : puissance et fiabilité pour les pros.

Innovation pratique, gestion simplifiée et absence de frais récurrents : UniFi se positionne comme un acteur solide sur un marché du NAS en pleine mutation. Attention, les NAS UniFi sont destinés au stockage en réseau uniquement.

The UniFi UNAS 2 NAS Review – Value vs Scale

Note, the UNAS Pro 2 is NOW LIVE on the UniFi Store . The UNAS 4, UNAS Pro 4 and UNAS Pro 8 are now in the site, but are not available till October / Q4 2025

The UniFi UNAS 2 is a compact, entry-level two-bay desktop NAS introduced as part of Ubiquiti’s second phase of NAS development, following the debut of the UNAS Pro in 2024. That earlier seven-bay rackmount system was notable for its low $499 price and integrated 10GbE connectivity, but it had an unconventional design, limited fan control, and no support for USB expansion. By contrast, the UNAS 2 shifts away from rackmount hardware and into the desktop market, adopting a much smaller form factor and prioritising simplicity over raw performance. Measuring 13.5 x 12.9 x 22.37 cm and weighing only 1.3 kg, it is one of the smallest systems in the UniFi NAS range and is constructed from polycarbonate rather than steel, reinforcing its role as an affordable, lightweight device.

The hardware is designed primarily for modest storage requirements, supporting two 3.5-inch hard drives with a maximum combined power budget of 52W and an overall consumption ceiling of 60W. The device operates on a single 2.5 GbE RJ45 interface, which also functions as a PoE++ input, removing the need for a conventional power supply unit but requiring either a compatible PoE++ switch or the included 60W injector. This approach marks a clear departure from the UNAS Pro, which included a standard power connector and optional redundancy through additional PSU modules. In practice, the reliance on a single port for both power and data streamlines installation within UniFi networks, but it also introduces a single point of failure and reduces flexibility compared with larger systems.

UniFi UNAS 2 Review – Quick Conclusion

The UniFi UNAS 2 is a compact, entry-level NAS that prioritises simplicity and integration within the UniFi ecosystem over flexibility or raw performance. Its use of PoE++ for both power and connectivity makes installation straightforward in environments with compatible UniFi switches, but it introduces reliance on a single port and limits deployment outside that infrastructure, even with the included injector in the retail kit. The system supports two 3.5-inch drives in a shared non–hot-swappable tray, with RAID 0, RAID 1, or single-disk setups available, but there is no option for expansion or NVMe caching. Hardware consists of a quad-core ARM Cortex-A55 processor with fixed 4 GB of LPDDR4 memory, which is efficient but imposes clear limits on throughput and application scope. Performance testing produced read speeds up to 260 MB/s and writes in the 160–180 MB/s range, sufficient for the 2.5 GbE interface but reflective of the modest hardware and thermal constraints, with CPU temperatures often approaching 80°C under load. Software provides a clean interface with snapshots, RAID tools, backups to other UniFi NAS or cloud services, and user management tied to UniFi identity, but features such as iSCSI, encryption, and granular backup rules are absent. As a result, the UNAS 2 is best suited as a secondary or edge storage device, particularly for UniFi users seeking easy integration, but it lacks the scalability and depth of established NAS platforms needed for primary or enterprise deployments.

Here are all the current UniFi NAS Solutions & Prices: UniFi UNAS 2 (2 Bay, $199) – HERE UniFi UNAS 4  (4 Bay + 2x M2, $379) – HERE UniFi UNAS Pro 4 (4 Bay + 2x M.2, $499) – HERE UniFi UNAS Pro (7 Bay, $499) – HERE UniFi UNAS Pro 8 (8-Bay + 2x M.2, $799) HERE

You can buy the UniFi UNAS 2 NAS via the link below – doing so will result in a small commission coming to me and Eddie at NASCompares, and allows us to keep doing what we do! 

 

UniFi UNAS 2 Review – Design

The UNAS 2 adopts a small desktop form factor, measuring 135 x 129 x 223.7 mm and weighing 1.3 kg. Its enclosure is constructed from polycarbonate, which makes it lighter and less industrial than the steel-based rackmount models in UniFi’s NAS range. The compact build is suited for environments where space is limited, and it operates within an ambient temperature range of -5 to 40°C and a humidity tolerance of 10–90% non-condensing. With only two drive bays, the UNAS 2 positions itself as an edge device for simple storage and backup, rather than a primary data management system.

Drive installation is handled through a single removable cage that holds both 3.5-inch drives. Each drive clips into place using a shared tray design, with both units inserted in opposite orientations to align with the SATA connectors. While this arrangement is functional, it has some limitations.

There is no support for hot swapping, meaning the system must be powered down before drives can be replaced. Additionally, the shared cage design requires both drives to be handled together, which increases the risk of disturbing a healthy drive when removing or replacing a failed one.

Cooling is managed by a small fan located at the rear, supported by passive ventilation channels at the base of the unit. Air is drawn in from underneath and expelled from the top section, ensuring airflow across the drives and the system board. Thermal tests recorded CPU temperatures in the range of 75–80°C during higher utilisation, with the chassis surface reaching around 39–50°C depending on workload.

The fan is adjustable via UniFi’s management interface, offering a choice between balanced operation and higher cooling at the expense of noise.

Noise levels ranged from 31–32 dBA in idle to 35–38 dBA under load, influenced heavily by the vibration of installed drives.

At the front of the unit, UniFi has integrated a 1.47-inch colour LCM display for system information. This provides basic details such as network status, storage health, and system alerts, but it is not touchscreen and cannot be used for configuration.

The lack of interactive control means that most management tasks still need to be handled through the UniFi OS console. LED indicators are also present for system status, and a physical locking mechanism is built into the drive cage, preventing accidental removal.

From a storage perspective, the UNAS 2 supports standard RAID configurations for two drives, namely RAID 0 and RAID 1, in addition to single-disk setups. Given the limitations of two-bay devices, RAID 1 is the most practical option, prioritising data protection over capacity.

The system officially supports large-capacity HDDs, with tests confirming compatibility up to 30 TB drives. However, there is no expansion capability through additional enclosures, and the single USB-C port on the front is limited to attaching external drives for storage or backups. This means users are confined to the internal two-bay maximum, making long-term planning important for deployment.

UniFi UNAS 2 Review – Internal Hardware

The UNAS 2 is built around a quad-core ARM Cortex-A55 processor clocked at 1.7 GHz. This CPU architecture is designed for efficiency rather than high computational output, which makes it suitable for low-power storage operations, but less capable for advanced workloads such as virtualisation, heavy encryption, or on-the-fly media transcoding.

During testing, CPU temperatures generally remained in the 75–80°C range under sustained use, dropping closer to 50–60°C when idle or under light activity. While these figures fall within operating limits, they reflect the modest cooling design of the enclosure and the limited thermal headroom of the ARM-based hardware.

The device includes 4 GB of LPDDR4 memory, which is soldered to the board and cannot be expanded. This fixed allocation is sufficient for handling RAID 1 synchronisation, snapshots, and standard multi-user file operations, but it sets a ceiling on the system’s multitasking capability.

Unlike larger UniFi NAS models that feature 16 GB of memory, the UNAS 2’s hardware is intended only for light to moderate workloads. Memory use during testing reached high utilisation during RAID synchronisation but did not exceed available capacity, suggesting that UniFi has provisioned enough for the intended use case, while keeping the system constrained to its role as an entry-level solution.

The operating system is stored internally and runs independently of the installed drives, leaving both bays available for data. This separation ensures that the system can still boot even if both drives are removed or replaced. Storage management is limited to the basic RAID levels supported by two-bay systems, and no M.2 NVMe slots are included for caching or tiered storage, a feature reserved for larger UniFi NAS models. As such, the internal hardware of the UNAS 2 reflects its role as a secondary or edge device, designed primarily for straightforward storage and backup within a UniFi-managed network.

UniFi UNAS 2 Review – Connectivity & Performance

The UNAS 2 relies on a single 2.5 GbE RJ45 port for both data and power, with PoE++ providing up to 60W of combined budget. This integration reduces cabling and eliminates the need for an external power brick, but it introduces a single point of failure. That said, the UNAS 2 retail kit DOES include a PoE mains adapter, so ultimately the end user does have the option of deploying in a traditional manner (though power and network connectivity are still funnelled into the same connector).

If the cable or port fails, both power and connectivity are lost. A 60W PoE++ injector is included in the package for users without a compatible PoE++ switch, but this approach remains less flexible than traditional dual-port NAS designs. There is no secondary network interface, Wi-Fi connectivity (rare in a system of this scale, but would allow for failover if it was), support of a USB network adapter or option for link aggregation, which makes the system dependent on one connection for all network and power needs.

In addition to the Ethernet port, the front of the device includes a USB-C interface rated at 5 Gbps. This provides the ability to attach external storage devices, enabling data import, backups, or temporary storage expansion. However, the USB port is limited to storage and does not support network adapters, UPS integration, or official expansion enclosures. While the addition of USB-C addresses one omission from the UNAS Pro, its functionality is constrained and focused solely on external drive access.

Network throughput reflects the limitations of a dual-drive ARM-based NAS. In testing with two 8TB HDDs in RAID 1, sequential read speeds reached around 260 MB/s, while write speeds varied between 160–180 MB/s depending on workload. Benchmarks such as AJA and CrystalDiskMark confirmed this pattern, with read performance consistently higher than write due to the processor’s handling of RAID and data caching. These figures make effective use of the 2.5 GbE interface but leave no capacity to challenge higher multi-gigabit standards.

Power consumption aligns with UniFi’s published specifications, averaging 16–17W in idle, 18–20W during light activity, and 23–24W under heavier use. Peak usage during sustained transfers with RAID synchronisation reached approximately 25W, well below the 60W ceiling. Thermal monitoring showed the CPU rising toward 79–80°C under stress, though the chassis fan helped bring temperatures back into the 50–60°C range once load reduced. These results indicate that while the system operates within its defined limits, sustained workloads push the ARM processor and cooling system close to their maximum operating range.

Noise levels were modest, with idle operation producing around 31–32 dBA and workloads raising this to 35–38 dBA. The shared dual-drive cage design contributed to additional vibration, particularly when placed on a hard surface. Rubberised feet help dampen this effect, but vibration noise was noticeably reduced when the device was placed on softer material such as foam. Overall, while the system remains relatively quiet, its acoustic profile is closely tied to the drives selected and the surface it rests on.

• Network Interface: 1 x 2.5 GbE RJ45 (PoE++)

• USB Ports: 1 x USB-C (5 Gbps, storage only)

• PoE Power Budget: 60W (52W available for drives)

• Power Supply: 60W PoE++ injector included

• Max Consumption: 60W (typical 16–25W during use)

• Tested Performance: ~260 MB/s reads, 160–180 MB/s writes (RAID 1, HDDs)

• Noise Levels: 31–32 dBA idle, up to 38 dBA under load

• Temperature Range (Observed): 75–80°C CPU under stress, 50–60°C idle/light use

UniFi UNAS 2 Review – Software and Services

The UNAS 2 runs on UniFi’s NAS management platform, which follows the same single-pane-of-glass interface design seen in the UNAS Pro and UNAS Pro 8. Administration is carried out via a web browser or through a ui.com account, with the option to disable cloud access and operate the system entirely on a local network.

The interface consolidates system status, storage health, user accounts, and backup management into one dashboard. While straightforward to use, it does not provide the same level of customisation or feature depth offered by longer-established NAS operating systems such as Synology DSM or QNAP QTS.

Storage management is limited by the two-bay architecture. Users can create RAID 0 or RAID 1 volumes, or operate drives independently. Drive health monitoring, temperature reporting, and snapshot scheduling are all included, allowing basic resilience and file recovery options.

Snapshots can be created and managed at the folder level, with the ability to lock snapshots to prevent deletion. Encryption, however, does not appear to be available on the UNAS 2, in contrast to larger UniFi NAS models where encrypted volumes are supported.

Backup functionality includes both system configuration and file-level options. Configuration backups can be stored locally or uploaded to a ui.com account, allowing the system to be restored quickly if reset or replaced. File-level backups extend to other UniFi NAS systems and selected cloud services, including Google Drive, with scheduling available for automation.

Local LAN backups to other storage devices via SMB are also supported, though filtering and exclusion rules are limited. The system is therefore capable of basic backup routines but lacks the more granular tools available on competing platforms.

User and access management is integrated into the UniFi ecosystem. Administrators can create local accounts or bind accounts to UniFi’s identity services, with two-factor authentication supported via the UniFi Verify app.

Permissions can be set at the folder level, and users can be restricted to LAN-only access if required. Supported protocols include SMB and NFS, but there is no iSCSI target functionality, limiting its application in virtualisation or editing workflows.

The software also includes fan control and system monitoring tools, but resource reporting is basic, with only CPU and memory utilisation graphs available.

Overall, the software reflects UniFi’s effort to balance simplicity with integration, but it remains less comprehensive than that of established NAS vendors.

UniFi UNAS 2 Review – Verdict and Conclusion

The UniFi UNAS 2 is presented as a compact and affordable two-bay NAS designed for straightforward storage and backup tasks, particularly within environments already using UniFi networking hardware. Its PoE++ design is distinctive, allowing both power and connectivity to be delivered over a single cable, simplifying installation where compatible PoE switches are available. This approach aligns with UniFi’s strategy of reducing external hardware requirements, though it also means that a failed port or damaged cable will disable both power and network access simultaneously. For non-UniFi users, the reliance on PoE++ creates an additional barrier, as adoption requires either compatible infrastructure or the included 60W injector. The shared dual-drive tray, lack of hot-swap support, and absence of expansion options further reinforce the system’s role as a fixed-capacity solution, best suited to smaller or secondary deployments. With a maximum drive budget of 52W and overall consumption limited to 60W, the device is power-efficient, but its architecture prioritises simplicity over flexibility.

On the software side, the UNAS 2 provides a user-friendly interface with access to snapshots, RAID configuration, system backups, and integration into the UniFi identity ecosystem. However, the limited hardware constrains the range of features available, and certain tools seen in UniFi’s larger NAS models are absent, such as encrypted volumes or extended network protocol support. Performance testing showed sequential read speeds up to 260 MB/s and write speeds around 160–180 MB/s, which make full use of the 2.5 GbE interface but leave little headroom for more demanding tasks. Thermals during extended use regularly pushed the CPU into the high 70s Celsius, and although fan management can be adjusted, sustained workloads highlight the limits of the system’s cooling design. The software’s omission of iSCSI and advanced backup filters also narrows its role, making it less competitive against established vendors in professional or virtualisation scenarios.

Ultimately, the UNAS 2 is most appropriately positioned as an edge or secondary NAS, providing basic networked storage for existing UniFi users who value plug-and-play deployment and ecosystem consistency, but it is not equipped to serve as a primary system in larger or more demanding environments (VMs, Containers, etc). A great and unique NAS that will nbe at it’s most appealing if you are already invested in the UniFi ecosystem, or have a NAS already that needs a network backup.

You can buy the UniFi UNAS 2 NAS via the link below – doing so will result in a small commission coming to me and Eddie at NASCompares, and allows us to keep doing what we do! 

Here are all the current UniFi NAS Solutions & Prices: UniFi UNAS 2 (2 Bay, $199) – HERE UniFi UNAS 4  (4 Bay + 2x M2, $379) – HERE UniFi UNAS Pro 4 (4 Bay + 2x M.2, $499) – HERE UniFi UNAS Pro (7 Bay, $499) – HERE UniFi UNAS Pro 8 (8-Bay + 2x M.2, $799) HERE

PROs of the UniFi UNAS 2 NAS

PROs of the UniFi UNAS 2 NAS

Benefits from almost a year of development of the UNAS Pro by UniFi, resulting in a much more complete solution in both hardware and software Exceptionally appealing price point Extremely low impact (power use, noise level, physical scale all great) Introduction of USB C 5Gb/s Connectivity is very welcome Supports complete network/local access if preferred, as well as full remote connectivity with the UI.com account and site manager services Wide Hard Drives and SATA SSD Support (UniFi branded drives and those from 3rd parties such as Seagate Ironwolf, WD Red and Toshiba N300) Comprehensive network storage software in UniFi NAS OS and Drive. Latest OS updates have included fan control, flexible RAID configurations, encrypted drive creation, customizable snapshots, more backup client choices/targets ‘Single Pane of Glass’ management and monitoring screen is very well presented! One of the fastest to deploy turnkey NAS solutions I have ever personally used!

Single network port, though not a dealbreaker (as this is still just 2x SATA throughput), is not great in terms of a network failover or in deployment of SATA SSDs Choice of PoE deployment unusual and although an adapter for mains power is included, is still not for everyone USB C connectivity does not support network adapters, NAS expansions or 3rd party UPS devices Very modest base hardware, but understandable relative to the price HDD injection is very unique, but it prevents hot swapping Still a lack of client applications native to the NAS services for Windows, Mac, Android and Linux

 

SUBSCRIBE TO OUR NEWSLETTER
[contact-form-7]
Join Inner Circle

This description contains links to Amazon. These links will take you to some of the products mentioned in today's content. As an Amazon Associate, I earn from qualifying purchases. Visit the NASCompares Deal Finder to find the best place to buy this device in your region, based on Service, Support and Reputation - Just Search for your NAS Drive in the Box Below

Need Advice on Data Storage from an Expert?

Finally, for free advice about your setup, just leave a message in the comments below here at NASCompares.com and we will get back to you. Need Help? Where possible (and where appropriate) please provide as much information about your requirements, as then I can arrange the best answer and solution to your needs. Do not worry about your e-mail address being required, it will NOT be used in a mailing list and will NOT be used in any way other than to respond to your enquiry. [contact-form-7] TRY CHAT Terms and Conditions   Alternatively, why not ask me on the ASK NASCompares forum, by clicking the button below. This is a community hub that serves as a place that I can answer your question, chew the fat, share new release information and even get corrections posted. I will always get around to answering ALL queries, but as a one-man operation, I cannot promise speed! So by sharing your query in the ASK NASCompares section below, you can get a better range of solutions and suggestions, alongside my own.

WE LOVE COFFEE

 

 

UniFi New NAS Rumours – Everything We Know

Duing the UniFi World Conference event (the UWC 2025 expo event that took place in several places around the world over a week in May) the brand took the opportunity to share a huge amount of information about their roadmap for hardware and software in 2025 (and 2026!) and although there was a lot of information about cameras, switches, integrations and improvements – the big, BIG detail that emerged that got my attention was that the UNAS series of NAS devices is rumoured to be getting several portfolio additions over the course of the next 18+ Months! All of this was seemingly shared behind closed doors, with photography and video prohibited during the presentations (with choice projects by the brand like these limited to keynote ‘on stage’ presentations) and not available for general access and sharing on the show floor.

However, ALOT of the information shared was then discussed at length on forums and community sites across the internet (unsurprisingly predominantly on Reddit more than most – shocker I know). Because of this, we have a great deal of rumoured, shared and near-confirmed information about what the brand is planning for the soon to be growing UNAS series of devices – including a potentially dedicated M.2 NVMe SSD flash devices, Enterprise grade ZFS Rackmount system (XG NAS?) and even more entry level desktop solutions in 2 and 4 Bay SATA.

There is a lot to get to and I think we will likely see granular and gradual updates to all of these solutions as time wears on, so I wanted to create this article to add shared info and leaks as they appear online. You can get notifications and alerts on this page by subscribing at the bottom of the article.

IMPORTANT – Regardless of how solid/rumoured any of the UniFi UNAS systems that are detailed on this page are – do NOT be complacent about your data and backups! If you need a backup solution right now/soon, do not ‘hold out’ for these devices, as no device will ever be worth the danger of your data being lost (power lose resulting in a raid failure, data corruption, accidental deletion..need I go on?). So, if you like the sound of UniFi and their products, and the UNAS from UniFi sounds like it meets your needs, it is still available RIGHT NOW for just $499 HERE – It is a 7x SATA Half-Depth Rackmout NAS with 10GbE and a comprehensive data management software in UniFi Drive. You can watch my review HERE and my 6 Months Later update on it HERE.

Here is a list of Sources on Reddit that detail what was observed at Unifi World Conference 2025 with regard to Network Attached Storage:

---

Which UniFi UNAS Devices Are Rumoured for 2025 and 2026?

16th June 2025 Updated

Below are the details we know so far (some details need further verification and confirmation, indicated appropriately) that we are aware of so far. Keep in mind (IMPORTANT) that these drives are massively ‘TBC’, so alongside potential name changes it is also possible that they may not arrive at all – as UniFi might change their mind based on market research about the need for a given device! Additionally, sometimes information online is contradictory to other information (eg the larger and smaller scale NAS system and a potential Pro XG system might well be the same device!), so do not treat this information as set in stone! Let’s break down each entry:

>>>>> IMPORTANT – IMAGES FOR GUIDANCE ONLY <<<<<

2 Bay Entry-Level HDD NAS

The UNAS Pro, although popular, is none the less quite large for much smaller user deployments – so if UniFi was to really stretch it’s muscles into the world of NAS, it would come as no surprise that they would provide more entry/small-footprint devices. So, the oft mentioned 2 Bay UNAS would be desirable, but also UniFi’s most compact HDD system to date, targeting home and SOHO users looking for simple backup or file-sharing functionality. No confirmation or detail on the shared information on the hardware profile (one can imagine an ARM base and 2-4GB of memory – but it’s all very ‘TBC’) and 2.5GbE connectivity. 2 drives would give precious little bandwidth for 10GbE to even be worth the time of day, even with SATA SSDs.

---

An NVMe SSD NAS dedicated NAS for Creative Workflows

This proposed SSD focused NAS moves away from spinning disks in favor of M.2 NVMe SSD slots, focusing on silent, high-performance workflows for media creators or prosumers. This compact unit maintains a passive cooling design and leverages Drive 3.0’s new dynamic storage pool system to balance protection and performance. It’s intended for those needing faster I/O than HDDs can provide without the size or noise of a rackmount. if this ends up coming out, is would be INCREDIBLY popular (given M.2 SSD prices are now only around 2x more than HDD, with a 4TB M.2 NVMe SSD in both Gen3 and Gen4 hitting just $200+, and WD Red and Seagate Ironwolf 4TB HDDs around the $89-99 mark)

---

4 Bay Desktop-Grade HDD NAS

This would deliver a more durable 4-bay solution with a desktop form factor, designed for small business environments or tech-savvy users. It combines the flexibility of 3.5″ HDDs with the enhanced features of UniFi Drive 3.0, including smarter snapshots and storage pools. Compared to the standard UNAS 2-bay discussed solution, this model would offer better RAID options, as well as performance potential (even in a RAID 5). Nevertheless, if/when this comes around, expect modest hardware under the hood!.

---

A ‘Proper’ 4 Bay and 8 Bay Rackmount NAS

Alongside the already released 7 Bay UNAS Pro, there is talk of a 4 Bay and 8-bay rackmount NAS aimed at larger deployments such as offices, branch networks, or video surveillance environments as a storage target for UniFi Portect perhaps. Built to handle RAID 6 (rolling ut in the latest UniFi NAS OS and Drive updates) and large-scale storage pools, it includes business-class hardware for redundancy and expandability. Its release aligns with Ubiquiti’s push into more scalable data solutions under the UniFi Drive 3.0 future framework.

---

An Enterprise ZFS Appliance – THIS IS WHERE IT GETS GOOD!

Although the existing UNAS Pro NAS system runs on an BTRFS foundation, there was multiple references and rumours to UniFi’s first foray into ZFS-based NAS systems and appears to be targeted at enterprise environments requiring snapshot-based backup, inline compression, and greater control over storage topology. Very few hardware specifics have been shared, and it is unclear whether this is a completely separate physical unit or a software SKU atop a Pro-series device. I will be interested to see if, if this arrives, how they will migrate the existing UNAS/Drive/NAS OS appliances onto this ZFS base – as well as whether it will benefit from the inline and native performance/integrity benefits of ZFS!

---